What Is the Maximum Transmission Distance for a Network Using 10base5 Technology?

The designation 10Base5 comes from the 10Mbps transmission speed and the maximum segment length of 500 meters. Its coaxial cable is identical to RG-8/U but has a stronger shield and braiding, making it very resistant to network interference.

Similarly, At what maximum distance would you have to add a repeater to a 10BASE2 network segment to prevent signal degradation?

The 10BASE2 standard defines a maximum segment length of 185 meters (that is, 607 feet).

Also, it is asked, Which transmission medium connector would connect each computer to the transmission medium?

—The transmission medium is UTP, and the connections are RJ-45.

Secondly, Which category of UTP should you install if you want to carry a maximum bandwidth of 250MHz?

If you wish to transport a maximum bandwidth of 250MHz, which kind of UTP should you use? Cat 6 cable, which consists of four twisted pairs, has a 250MHz rating.

Also, Which of the following is a connector type used with coaxial cabling?

The Bayone-Neill-Concelman (BNC) connection is the most common form of coaxial cable connector (See fig. 4).

People also ask, When we use repeater then maximum length of 10 base2 cable is meter?

A single section of a 10Base2 network may be 185 meters long. If larger lengths are necessary, repeaters must be used to link two or more segments.

Related Questions and Answers

Which transmission media has the highest transmission speed in a network?

In a network, which transmission medium gives the fastest transmission speed? Fiber optics, among the aforementioned technologies, is thought to have the fastest transmission speed. The transmission speed through fiber optics is 1000 Mb/s. The IEEE standard for it is 802.3z, and it is known as 1000Base-Lx.

Which wired media is useful for long distance communication?

Optic fiber cables are ideally suited for long-distance data transport and communication due to their increased bandwidth and high-quality performance.

HOW FAR CAN signals on an MMF cable travel?

Depending on the specification, MMF can transmit up to 10Gbps for up to 300 meters.

What is the max speed of Cat5e?

CAT5e and CAT6 both provide rates of up to 1000 Mbps (Gigabit per second). This is more than enough for the vast majority of internet connections.

What speed is Cat7?

10.000 Mbit/s (megabits per second)

What is the standard coax connector?

The F connection (also known as the F-type connector) is a coaxial RF connector that is often used with RG-6/U or RG-59/U cable for “over the air” terrestrial television, cable television, and worldwide for satellite television and cable modems. Eric E. developed the F connection.

What is 10Base5 and 10Base2?

10Base2—An Ethernet phrase referring to a maximum transmission rate of 10 Megabits per second via baseband signaling, with a maximum of 2 segments and a continuous cable segment length of 100 meters. 10Base5—An Ethernet term that refers to a maximum transmission rate of 10 Megabits per second over a baseband connection.

What is the maximum size of a 10Base2 network using 5 repeaters?

A 10Base2 network may therefore extend up to 925 meters, whereas a 10Base5 network could span up to 2,500 meters, according to the rule that there can only be 5 segments in a series and 4 repeaters between these 5 segments, with only 3 of the segments being occupied with devices.

What is the maximum number of repeaters for an Ethernet LAN?

Only five segments may be linked by four repeaters, or concentrators, and only three of the five segments can be mixing segments, according to the norm. Only 10BASE5, 10BASE2, and 10BASE-FP Ethernet segments are subject to this requirement.

What will be the transmission delay of 10Base2?

What is the propagation delay for a 10Base2 cable with a length of 185 meters? Any two network nodes may have a maximum of 5 segments (with 4 repeaters) along the path: 3 coax segments with a maximum delay of 0.949 uSec and 2 link segments with a maximum delay of 0.949 uSec.

What are the Ethernet LANS 10Base2 10BASE5 and 10BaseT?

10Base5 is an Ethernet phrase that refers to a maximum transmission rate of 10 Megabits per second via baseband signaling across five continuous segments of no more than 100 meters each. 10BaseT is an Ethernet word that refers to a maximum transmission rate of 10 Megabits per second over twisted pair cable using baseband signaling.

What is the maximum speed of a 1000BASE T cable?

a gigabit of data per second

Which of the following media has the greatest transmission distance capability?

Fibers Optical Optical fibers are the safest cable medium available. Installation and upkeep are time-consuming and expensive. When compared to coaxial and twisted pair connections, fiber optic cables have a faster transmission speed, a higher bandwidth, and the signal may traverse longer distances.

Which of the computer network is the largest?

The World Wide Web

What transmission media provides?

Forum for discussion Which transmission medium in a network has the fastest transmission speed? b.coaxial cable with twisted pairs a.optical fiberd.electrical cable b.optical fiberd.electrical cable c.optical fiberd optical fiber is the answer. 1 more row to go

What is transmission in networking?

The transmission mode describes how data is sent between two devices linked by a network. Communication Mode is another name for it. These modes control the direction of information flow.

What are the two kinds of transmission?

Direct and indirect contact transmission are the two forms of contact transmission. When an infected individual comes into physical touch with a vulnerable person, direct contact transmission occurs. When there is no direct human-to-human touch, indirect contact transmission occurs.

What are types of data transmission?

Serial transmission is divided into two types: synchronous and asynchronous. Bit synchronization is used in each of these transmission systems. Bit synchronisation is required to determine the start and finish of data transfer.

Which fiber is used for long distance transmission?

Single-mode fibers are utilized for long-distance data transmission at high speeds. Multimode fibers are more prone to attenuation than singlemode fibers.

Which is the cable used for the fastest communication in the network?

In networks, coaxial cables are utilized to enable for rapid communication.

What is wired transmission media?

Twisted pair cable, Ethernet cable, coaxial cable, and optical fibre are examples of wired transmission medium, while microwave, radio wave, satellite, infrared, Bluetooth, and WIFI are examples of wireless communication media.

What is the maximum segment length that is specified by the 1000BASE T standard?

The 1000BASE-T standard (also known as IEEE 802.3ab) is a gigabit Ethernet over copper wire standard. Each 1000BASE-T network segment may be up to 100 meters long and must utilize at least Cat 5 cable. It’s also possible to utilize Cat 5e or Cat 6 cable.

Which of the below network cabling options offers the longest possible segment length?

Explanation: In compared to copper cables, fiber-optic cable has substantially reduced attenuation, crosstalk, and interference, allowing it to reach lengths of many kilometers.

Which IEEE 802 standard defines a bus topology using coaxial baseband cable and is able to transmit at 10mbs?

Explanation: The IEEE 802.3 standard initially called for using a bus architecture with coaxial baseband wire to transport data at speeds of up to 10 Mbps.

How far can Cat6?

328 meters

Is Cat 6 faster than Cat 5e?

Cat 6 is more expensive and quicker than Cat 5e, but its range is restricted. Due to the cable’s increased insulation, Cat 6 offers data transmission rates up to 10 Gbps @ 250 MHz with much less (or no) crosstalk interference. Its 10 Gbps speed, however, is only effective up to 164 feet.

Conclusion

This Video Should Help:

The “which physical layer network device broadcasts all incoming packets out all available ports?” is a question that you might ask if you are trying to set up a wireless network. The answer to this question will be the maximum transmission distance for a 10base5 technology.

  • which of the following is a valid mac address?
  • which of the following is classified as an apipa address
  • which of the following is a mac address?
  • which of the following is true concerning the function of a switch
  • which of the following is not an advantage of using dynamic routing protocols
Scroll to Top